Sunday, 10 August 2025

Braced Handle Bars

 OEM handlebars for the Himalayan have reputation for being a bit soft. When the bike hits the ground, as it likely to do off road, the impact on the bars can bend them. Having binned it but not bent the bars I thought it might be time for an upgrade. The old bars are silver coloured the new ones are black. I see it as a nice aesthetic too. Below is the old look.

First job is too remove the hand guards. An Allen key in the bar end removes the guard and the weight. When I removed the first bolt I tried it in the captured nut in the new bars to makes sure it fitted. No point continuing if it did not fit. It did so I was happy to move on. A 14mm spanner was needed to loosen the check nut on the mirror stalk. Once loose the mirror could be removed. Another Allen bolt acted as a pinch bolt securing clutch lever assembly to the bike. The bolt removed. It was at this point a nut fell off the bike as did the Oxford heated grip controller. Nothing lost or damaged. Note to self remember the heated grip controller is secure by a 10mm nut under the clutch lever pinch bolt. I should say that any fixings removed from the bike were put in the magnetic tray. Hopefully when the job is done the tray is empty! A Phillps screw secures the switch cluster, grips and "choke lever" to the bars. I give it a twist. It moves but is very tight. There is a cable tidy which fits into a hole in the underside of the handle bar. It comes out with a fight. It is damage so it is discarded. There is an aftermarket switch for the riding lights. Two small screw secure the switch. They are removed.  Moving to the right side. Two Philips screws secure the switch cluster and throttle twist grip. Two Allen bolts secure the brake reservoir and lever. These come off in the normal way. There is a cable tidy which fits into a hole in the underside of the handle bar. It comes out with a fight. It is damage so it is discarded. The bars are secured to the upper yoke by four Allen bolts. They are very tight. I worry I might snap at least one of them. I give each one a small squirt of 3 in 1 oil. This does ease them a little. I find that red Locktight has been used on them, quite unnecessarily. The Locktight gives in and the bolts are wound out with some effort. Nothing snapped. The handle bars are now loose. It is necessary to remove the left side equipment first. The hand grip is very tight but it does move. Twisting backwards and forward and pulling at the same time works the grip off the bar. The clutch lever mount slips off quite easily. The bars can be pulled to the left which gives the necessary leeway to remove the throttle twist grip and cluster. We are fully committed now!

 

The new an old and new bars are subtly different to each other. The new bars are slightly raked back and up from the straighter and flatter  OEM items. There is the brace and the colour. The new items came from Hitchcocks. See the link in the side bar.   


 

Old v new bars

  To fitting of the new bars is the reverse of removing them. The throttle twist grip is slip on. The bar are pushed the right. The clutch lever mount is slipped on and pushed up the bars. The switch cluster and grip is force back on with a twisting motion. There is a residue of glue which will, no doubt, secure he grips as before. Now the clusters are in place the four bolts and the handle bar cap is refixed and bolts nipped up. They will be adjust later. On the inside of each cluster there is a locating pin. On the handle bar there is a hole. It was a bit fiddly to get he cluster with it pin the line up with the hole. A bit wiggling and check made the pin and holes line up. The bolt for the clutch lever is relocated and nipped up. The heated grip controller is refitted and 10mm nut and washer refitted. The right side the brake reservoir and lever is reattached and nipped up. I sit on the bike and move the handle bars to where I think  they feel right. I nip up the handlebar cap bolts to the correct setting. I tighten the screws of the left cluster making sure the "choke lever" operated correctly. The aftermarket switch for the riding lights has a brass coloured strap. When I removed the switch I took the strap and painted it black with rattle can. The painted strap is refitted. I adjust the attitude of the switch to make it easier to use. On the right side I tighten the screws for the switch cluster. I find the play in the throttle cable has disappeared. On the old bars there was significant amount of slack so when you twisted the throttle I had to take up more slack than I would like before the throttle actuated. 

With everything back in place I did an switch check. I turned the bike withe  key and went through each switch to make sure it activated the appropriate light. I also pulled the front brake lever to see if the rear brake light worked...it did. With some trepidation I hit the starter button. The bike cranked and started. I flicked the throttle a couple of times. It snapped back into place. The bike responded to the inputs and settled back to the normal tick over. The disappearing slack could have gone too far and pulled the throttle open at idle speeds. It did not and that is a result. I took the bike for a very quick spin to see that everything was in order.      

New handle bars

 I like the new aesthetic. You can see the slight rake to the bar if you compare the before and after pictures. There might be some subtle adjustment to be made the position of the bars and controls. I won't know until I go for an extended ride. I will take an Allen key and screw drive with me. I am hoping the raked bars will more comfortable on my wrists. Time will tell.