Tuesday, 29 July 2025

Rationalising the rats nest

The Himmy has a few additional accessories, riding lights and heated grip which came with the bike and a Sat Nav which I fitted. When lifted the seat to wire in the sat Nav I was presented with a rats nest of non-factory wiring. Wires were of differing sizes, bullet connectors, some soldered joint, some poorly wrapped with electrical tape others loosely shrink wrapped. I decided it needed tidying up.
 
I looked around the interweb for a box that would act as a distribution board. The idea was that a box would take a feed from the battery and the various accessories would be feed from the box. It also had to be small enough to fit under the seat. There are very few hidey holes on the himmy. I found the very thing in the Quick Wiring Fuse Box Battery Protection Junction Box. For this job the fuel tank and seats had to be removed. The seat come off easily but the tank needs two electrical connectors, fuel line and breather hoses to be disconnected.
 
 
  The DC 12v connects to the battery and there are four sets of terminals for the accessories. Each terminal set has a fuse, the blue LED means the circuit is good. It switches to red when there is an issue on the circuit. This sounds great except being directly connected to the battery and running the LEDs it means it will kill the puny battery on the bike in no time. I needed to find a switched feed from the bike so when the key is switch to off the accessory box is shut down as well. Part of the rats nest contained a switched feed. First the junction box had to be found a home that easily accessed. There is a scoop in the rear fender which accommodates the tool kit which is located under the rear seat. With the tool kit removed the junction box fitted in the space without affecting the fit of the seat. The box came with double sided tape. It was just a matter cleaning the place where the box was to live, fitting the tape to the box and the box to the fender. 
 
The 12v DC cable was threaded through the bike to be near the battery. The black (Negative) connector slipped snugly under the negative battery terminal. I just had to join the red wire from the box to the switched feed. The red wire from the box and switch feed wire were cut to slightly over length, the insulation stripped back and the wired twisted together and soldered. The joint was tightly wrapped with tape and tucked into the space between the frame and wiring harness. Now the power feed to the box reacted to the position of the ignition key.
 
The next job was to figure out what all the wires served and where they went. The Oxford heated grip had a nice long, paired wire which was connected the battery terminals. I disconnected the paired wires from the battery. I was necessary to cut off the inline fuse. It was no longer needed. The each outlet on the junction box is fused. This made the job of threading the wires thought frames to the junction box. The paired wires where cut to length, the insulation stripped and in this case the bare copper strands were tinned. This makes a tidy and secure base once they are pushed into their respective terminal and the screws fastened. The riding lights were a bit awkward. The wires feeding the lights were hacked into the main wiring loom. This meant they were always on. They also had some dodgy connectors and taping. Once I figured out the connection I tidied up the wires by cutting them back and soldering them together and covering with proper fitting heat shrink. The negatives from the lamps were earthed to the bike's frames. Having found the positive feed I routed that back to the junction box, cu the wire to length and stripped and tinned the end before connecting it to the junction box.
 
Fuse protected distibution box


The last accessory to tackle was the Sat Nav. To make it interesting the Sat Nav unit is over the handles bars and the junction box is under the rear seat. The power cable is quite long but would in be long enough? I started in the middle next to the battery. I threaded the Sat Nav power connector along the back bone of the frame, followed the wires path past the steering head and onto the instrument cluster. From there the wire was routed up the side and along the accessory bar to the Sat Nav mounting point. I had to fit the power lead into the Sat Nav cradle then attach the cradle to the mount. The cradle allows the Sat Nav unit to be quickly removed from the bike. The ball mount allows the cradle to positioned in front of the rider (me) where I read it with ease. I put small cable ties at likely points. The were loose for now. The reason for starting in the middle is that the Sat Nav power lead has a big blast resistor. It was easier for that to stay put and thread the small head unit to the mounting point. It took a little while to locate a home for the resistor unit to be fixed so that it did not foul the rider seat. It is about the size of a match box (35 x 25 x 20mm)  I found a recess in the air box which accommodated the resistor without fouling the seat. Double sided tape held in position. The wires from the resistor were led in and round the frame and wiring harness to the junction box. The wire were just long enough. The ends were already tinned so they were just plugged in the terminals and tightened up. All the wires were then tucked in next to the harness and zipped tied to secure them. 
 
Instrument cluster for the Himmy 411

      
 All the accessories were checked that they continued to work and obeyed the key. They did. Then it was case of refitting the tank which is a bit fiddly especially as it was full of petrol. The seat were fitted and rechecking everything worked and nothing was pinched. 
 
Spare wires and connectors

 The bikes is just a few ounces lighter than it was but it is a whole lot tidier and there is room for another powered accessory. I wonder what that shall be? 
 
Update: 
The bike has been stood for a few days and the bikes still has enough umph in the battery to start the bike. I am calling that a result.