Sunday, 10 August 2025

Braced Handle Bars

 OEM handlebars for the Himalayan have reputation for being a bit soft. When the bike hits the ground, as it likely to do off road, the impact on the bars can bend them. Having binned it but not bent the bars I thought it might be time for an upgrade. The old bars are silver coloured the new ones are black. I see it as a nice aesthetic too. Below is the old look.

First job is too remove the hand guards. An Allen key in the bar end removes the guard and the weight. When I removed the first bolt I tried it in the captured nut in the new bars to makes sure it fitted. No point continuing if it did not fit. It did so I was happy to move on. A 14mm spanner was needed to loosen the check nut on the mirror stalk. Once loose the mirror could be removed. Another Allen bolt acted as a pinch bolt securing clutch lever assembly to the bike. The bolt removed. It was at this point a nut fell off the bike as did the Oxford heated grip controller. Nothing lost or damaged. Note to self remember the heated grip controller is secure by a 10mm nut under the clutch lever pinch bolt. I should say that any fixings removed from the bike were put in the magnetic tray. Hopefully when the job is done the tray is empty! A Phillps screw secures the switch cluster, grips and "choke lever" to the bars. I give it a twist. It moves but is very tight. There is a cable tidy which fits into a hole in the underside of the handle bar. It comes out with a fight. It is damage so it is discarded. There is an aftermarket switch for the riding lights. Two small screw secure the switch. They are removed.  Moving to the right side. Two Philips screws secure the switch cluster and throttle twist grip. Two Allen bolts secure the brake reservoir and lever. These come off in the normal way. There is a cable tidy which fits into a hole in the underside of the handle bar. It comes out with a fight. It is damage so it is discarded. The bars are secured to the upper yoke by four Allen bolts. They are very tight. I worry I might snap at least one of them. I give each one a small squirt of 3 in 1 oil. This does ease them a little. I find that red Locktight has been used on them, quite unnecessarily. The Locktight gives in and the bolts are wound out with some effort. Nothing snapped. The handle bars are now loose. It is necessary to remove the left side equipment first. The hand grip is very tight but it does move. Twisting backwards and forward and pulling at the same time works the grip off the bar. The clutch lever mount slips off quite easily. The bars can be pulled to the left which gives the necessary leeway to remove the throttle twist grip and cluster. We are fully committed now!

 

The new an old and new bars are subtly different to each other. The new bars are slightly raked back and up from the straighter and flatter  OEM items. There is the brace and the colour. The new items came from Hitchcocks. See the link in the side bar.   


 

Old v new bars

  To fitting of the new bars is the reverse of removing them. The throttle twist grip is slip on. The bar are pushed the right. The clutch lever mount is slipped on and pushed up the bars. The switch cluster and grip is force back on with a twisting motion. There is a residue of glue which will, no doubt, secure he grips as before. Now the clusters are in place the four bolts and the handle bar cap is refixed and bolts nipped up. They will be adjust later. On the inside of each cluster there is a locating pin. On the handle bar there is a hole. It was a bit fiddly to get he cluster with it pin the line up with the hole. A bit wiggling and check made the pin and holes line up. The bolt for the clutch lever is relocated and nipped up. The heated grip controller is refitted and 10mm nut and washer refitted. The right side the brake reservoir and lever is reattached and nipped up. I sit on the bike and move the handle bars to where I think  they feel right. I nip up the handlebar cap bolts to the correct setting. I tighten the screws of the left cluster making sure the "choke lever" operated correctly. The aftermarket switch for the riding lights has a brass coloured strap. When I removed the switch I took the strap and painted it black with rattle can. The painted strap is refitted. I adjust the attitude of the switch to make it easier to use. On the right side I tighten the screws for the switch cluster. I find the play in the throttle cable has disappeared. On the old bars there was significant amount of slack so when you twisted the throttle I had to take up more slack than I would like before the throttle actuated. 

With everything back in place I did an switch check. I turned the bike withe  key and went through each switch to make sure it activated the appropriate light. I also pulled the front brake lever to see if the rear brake light worked...it did. With some trepidation I hit the starter button. The bike cranked and started. I flicked the throttle a couple of times. It snapped back into place. The bike responded to the inputs and settled back to the normal tick over. The disappearing slack could have gone too far and pulled the throttle open at idle speeds. It did not and that is a result. I took the bike for a very quick spin to see that everything was in order.      

New handle bars

 I like the new aesthetic. You can see the slight rake to the bar if you compare the before and after pictures. There might be some subtle adjustment to be made the position of the bars and controls. I won't know until I go for an extended ride. I will take an Allen key and screw drive with me. I am hoping the raked bars will more comfortable on my wrists. Time will tell.    

Rear hugger

The hugger is a small mud guard that is fitted to the swing arm. It protects the shock absorber and the back the electric casing from the road crud thrown around by the rear tyre. This upgrade was a little more involved. 


                 

First the rear wheel had to come out. That involved breaking the chain at the link. Loosening the 24mm nut that secure the axle. The axle is removed and then the wheel can be removed. Then the area was thoroughly washed. It is difficult the clean this are with the wheel in place. I had a cup of tea and read the instructions whilst the area dried. 


 

The cable ties which were supplied in the kit were threaded though the upper slot as per the instructions. The swing arm fit in the recess. It is a snug fit and I tapped it home with the handle of my hammer. The cable ties were threaded around the swing arm and out through the bottom slot in the hugger. The ties were pulled tight, a further tap with the hame the make sure the hugger was fully seated and the ties took up a little slack. The hugger was fixed. The trimmed off the excess from the ties and that part of the job was done.

The last part was to refit the back wheel. The axle had to threaded through the near side swing arm picking up the chain adjuster on the way, this whilst holding the tyre off the road and keeping the chain ring and cush drive in the wheel. Wiggling the wheel and axle made it slip through the wheel hub, next the spacer had to be collected then the rear brake assemble this time whist ensure the disc brake pads went neatly either side of the disc rotor. Then to collect the off side chain adjuster then finally slip on the big washer and 24mm axle nut. The axle nut is just nipped up. The drive chain has to reconnected by offering up the chain to accept the split link. It was about now a realised why I have had bikes with shaft drives for years.For whatever reason the chain did not want get close enough for the fitting of the split link. I made sure the chain adjusters were slack, the axle loose enough to move and the chain was on the sprocket at the correct place. There was no reason it should not go back together. The chain is quite worn and lose. Close but not close enough. I remember an odd trick for this situation.

 

A cable tie is looped around the adjacent rollers and pulled tight. I spun the wheel backwards and forwards and low, the link came together. The split link was slid into lace. "o" rings slipped over the pins, the side plate installed a squeezed home finally the circlip was fitted remembering to put it one the right way - the fish swims up stream i.e closed end in the direction of rotation. And don't forget the remove the cable tie. Lastly the chain was adjusted to have 15 - 20mm of free play and the wheel to be on centre line of the bike. That quicker said than done. 

 

The hugger is quite out of sight. However, I expect it will help keep the worst of the road debris of the rear suspension unit and prolong its life. 

                                             




Fender Extender

 The fender extended will hopefully keep a bit more crud of the front of the engine. The existing mud guard does a reasonable job and the engine bash plate helps too. The bike already came with spacers to raise the front mud guard so mud does not clog between the tyre and guard. The extender was a cheap upgrade and a easy fix. 


 First I removed the four bolts holding the mud guard. The underside of the guard got a good washing. Any dirt would not help the extender sticking. I offered up the extender the mud guard and marked the edge. The kit comes with a cloth embedded with a cleaner. The cloth was rubbed all over the marked area on the underside the mud guard and opposite face on the extended.

 


 Next job was to arrange a stick the double side sticky pads to the extender. I also removed the makers sticker. I carefully peeled off the protective backing the sticky pads. Then ever so carefully positioned the extender under the mud guard and aligned the two parts. There was no second chances. The two elements were joined. they lined up nicely. 


 The kit contained four of these fiddly body poppers. An eight millimetre hole was drill at four points around the edge of the extender. The holes were cleaned up and popper inserted. The button was pressed down to secure the popper. Easy to do just fiddly and you have to be careful not to damage the finish on the existing mud guard.

 


 The top edge of the extender just need trimming back to make a smooth line into the existing mud guard. The mud guard was put back in place the risers and the fours bolts done up. Another small and cheap upgrade from Hitchcocks 

Head Light Stone Guard

 The guard is just a mesh to guard against something smashing the head light. Its not a problem I expect. I just got it for a bit of fun. There are many styles of head light guards. I went with a classic wire type from Hitchcocks.

Head light guard from Hitchcocks
The kit came with aluminium spaces and allen key bolts. 

The fitting was easy. I cleaned the headlight before I started. I undid the existing head light retaining Philips screws.Offered up the guard, slipped the spaced into place and screwed in the Allen bolts. I did one side at a time. Lining up the second bolt was a but fiddly until a moved the guard around on the headlight. The guard found it place and the bolt dropped into place. 

Head light before guard
Head light before   

 
Head light after guard
Head light after

The part fitted well. I expected it to sit a bit further away from the glass. I also think cleaning the head light is going to a trial.