It has been a while since I had a chain driven bike. I have been lubing the chain before and after runs but it is sounding noisy. The test is to go to the back of the bike and see if you can pull the chain away from the sprocket. If you can see daylight between the chain and the teeth then its time to replace the chain. Since the chain engages with the front and rear sprocket they will wear too. It is recommended the change the sprockets at the same time as the chain.
I took the bike to the new container which is set out as my garage/workshop. The job is straight forward but with one big hurdle. The drive sprocket which take power from the engine is usually very tight and for good reason. There is a soft washer that is flattened over the nut that secures the drive sprocket to the gearbox output shaft. To get that big nut one has to remove the engine cover which protect the rider's feet from the spinning sprocket and chain. 2 x 8mm bolts. Easy job...er no. The bottom bolt rounded off instantly. The last person that had the bolt off tightened it to a heroic torque level. The old fashion method for removing rounded heads was employed....a hammer and cold chisel. Being careful not the smash the casing I used the chisel to release the grip of the thread. The bot spun out once it grip was released. I need a new bolt! Once the casing was off the soft washer tab was chiselled back and a 30mm socket and long bar was need to release the not holding the drive sprocket on. I put the bike in gear, went round the right side of the bike and stepped on the back brake pedal. I leaned across the bike and pulled on the long lever. A couple of tugs and groans the nut came loose.I figured there was not much point doing anything else until I got this big nut off.

The old drive sprocket was a little worn but still had lots of life in it. With that hurdle crossed I went with a easier tasks off removing the chain and rear wheel. The chain was stiff with dirt and chain rollers were shiny with wear, neither are a good sign. Next task to remove the six bolts that hold the rear sprocket to the cush drive plate. Nothing difficult to over come.

The sprocket was not too bad but one could see the wear. The new sprocket was bolted to to the cush drive plate. The cush drive plate put back in the wheel hub. I wiggled to estimate the wear. There was none. The back wheel was refitted. This is always a tricky job on a chain drive. The axle has the pass thought the swing arm, then the chain adjuster, then the hub, then spacer then the rear brake carrier which has to be aligned with the torque inhibitor then the second chain adjuster and finally the another arm of the swing arm. Then a washer and 24mm nut are fitted and done up until it pinches but not tightened. The chain adjusters are slacked right off and the wheel pushed as far forward as it will go. The new chain is then fed around the rear sprocket then the front sprocket and chain should meet up. At this point a split link is inserted between the two ends of the chain to make it a continuous chain. This can be fiddly. I discovered a great hack. Take a zip tie and feed it round the roller of the last links. Pull the zip tie tight. It pulls the two end of the chain together making the fitting of the split link less difficult. Chain on then we need to make sure the rear wheels is in the centre line of the bike making the front and rear wheel are in line. This can be done using the markers on either side of the swing arm. That two can be fiddly and inaccurate.
I picked up a laser chain alignment tool at a recent bike event at Donnington Park. It clips the rear sprocket. I had to take the chain guard off to use the laser. 2 x 20mm bolts so no trouble. The laser point along the centre line of the chain. The chain adjusters are used make the laser dot sit in the centre of the chain. It is great tool because there is another dimension to chain adjustment. The chain needs to have some slack to deal with the suspension travel. Centring the chain and therefore the rear wheel makes the bike track and corner properly and reduces excessive wear on the chain and tyre.
If you look closely you will see the red dot of the laser
The chain guard was refitted. Now the chain was on the 30 mm nut on the drive sprocket could be tightened up. It was the same procedure as for loosening the nut but in reverse. With the nut tightened and lock washer tabbed over the drive sprocket cover could be refitted. The new chain was covered in the grease from the factory. I spun the rear wheel to make sure the chain ran smoothly. I did and was really quiet. I started the bike on the main stand and put in gear. The rear wheel spun nicely. I ran a little extra chain lube over the moving chain to lube the sprockets. The ride home was really smooth from the drive train. The new chain and sprockets made a difference.