Saturday, 18 July 2026

Luggage Panel

 This was a very quick upgrade. The luggage panel replaces the rear passenger seat. It simply locates in the same catches as the passenger seat. It take two seconds to fit. No tools required 


 It will make carrying kit easier. The rear seat whilst useful is not a great platform for carrying bags or equipment.  

 

https://accessories.hitchcocksmotorcycles.com/45232?cont_page=Royal-Enfield-Himalayan-Accessories&Page=2 

New chain

 It has been a while since I had a chain driven bike. I have been lubing the chain before and after runs but it is sounding noisy. The test is to go to the back of the bike and see if you can pull the chain away from the sprocket. If you can see daylight between the chain and the teeth then its time to replace the chain. Since the chain engages with the front and rear sprocket they will wear too. It is recommended the change the sprockets at the same time as the chain.

I took the bike to the new container which is set out as my garage/workshop. The job is straight forward but with one big hurdle. The drive sprocket which take power from the engine is usually very tight and for good reason. There is a soft washer that is flattened  over the nut that secures the drive sprocket to the gearbox output shaft. To get that big nut one has to remove the engine cover which protect the rider's feet from the spinning sprocket and chain. 2 x 8mm bolts. Easy job...er no. The bottom bolt rounded off instantly. The last person that had the bolt off tightened it to a heroic torque level. The old fashion method for removing rounded heads was employed....a hammer and cold chisel. Being careful not the smash the casing I used the chisel to release the grip of the thread. The bot spun out once it grip was released. I need a new bolt! Once the casing was off the soft washer tab was chiselled back and a 30mm socket and long bar was need to release the not holding the drive sprocket on. I put the bike in gear, went round the right side of the bike and stepped on the back brake pedal. I leaned across the bike and pulled on the long lever. A couple of tugs and groans the nut came loose.I figured there was not much point doing anything else until I got this big nut off. 


 The old drive sprocket was a little worn but still had lots of life in it. With that hurdle crossed I went with a easier tasks off removing the chain and rear wheel. The chain was stiff with dirt and chain rollers were shiny with wear, neither are a good sign. Next task to remove the six bolts that hold the rear sprocket to the cush drive plate. Nothing difficult to over come. 

  The sprocket was not too bad but one could see the wear. The new sprocket was bolted to to the cush drive plate. The cush drive plate put back in the wheel hub. I wiggled to estimate the wear. There was none. The back wheel was refitted. This is always a tricky job on a chain drive. The axle has the pass thought the swing arm, then the chain adjuster, then the hub, then  spacer then the rear brake carrier which has to be aligned with the torque inhibitor then the second chain adjuster and finally the another arm of the swing arm. Then a washer and 24mm nut are fitted and done up until it pinches but not tightened. The chain adjusters are slacked right off and the wheel pushed as far forward as it will go. The new chain is then fed around the rear sprocket then the front sprocket and chain should meet up. At this point a split link is inserted between the two ends of the chain to make it a continuous chain. This can be fiddly. I discovered a great hack. Take a zip tie and feed it round the roller of the last links. Pull the zip tie tight. It pulls the two end of the chain together making the fitting of the split link less difficult. Chain on then we need to make sure the rear wheels is in the centre line of the bike making the front and rear wheel are in line. This can be done using the markers on either side of the swing arm. That two can be fiddly and inaccurate.  

I picked up a laser  chain alignment tool at a recent bike event at Donnington Park. It clips the rear sprocket. I had to take the chain guard off to use the laser. 2 x 20mm bolts so no trouble. The laser point along the centre line of the chain. The chain adjusters are used make the laser dot sit in the centre of the chain. It is great tool because there is another dimension to chain adjustment. The chain needs to have some slack to deal with the suspension travel. Centring the chain and therefore the rear wheel makes the bike track and corner properly and reduces excessive wear on the chain and tyre.  

If you look closely you will see the red dot of the laser

  The chain guard was refitted. Now the chain was on the 30 mm nut on the drive sprocket could be tightened up. It was the same procedure as for loosening the nut but in reverse. With the nut tightened and lock washer tabbed over the drive sprocket cover could be refitted. The new chain was covered in the grease from the factory.  I spun the rear wheel to make sure the chain ran smoothly. I did and was really quiet. I started the bike on the main stand and put in gear. The rear wheel spun nicely. I ran a little extra chain lube over the moving chain to lube the sprockets. The ride home was really smooth from the drive train. The new chain and sprockets made a difference.     

           

Sunday, 10 August 2025

Braced Handle Bars

 OEM handlebars for the Himalayan have reputation for being a bit soft. When the bike hits the ground, as it likely to do off road, the impact on the bars can bend them. Having binned it but not bent the bars I thought it might be time for an upgrade. The old bars are silver coloured the new ones are black. I see it as a nice aesthetic too. Below is the old look.

First job is too remove the hand guards. An Allen key in the bar end removes the guard and the weight. When I removed the first bolt I tried it in the captured nut in the new bars to makes sure it fitted. No point continuing if it did not fit. It did so I was happy to move on. A 14mm spanner was needed to loosen the check nut on the mirror stalk. Once loose the mirror could be removed. Another Allen bolt acted as a pinch bolt securing clutch lever assembly to the bike. The bolt removed. It was at this point a nut fell off the bike as did the Oxford heated grip controller. Nothing lost or damaged. Note to self remember the heated grip controller is secure by a 10mm nut under the clutch lever pinch bolt. I should say that any fixings removed from the bike were put in the magnetic tray. Hopefully when the job is done the tray is empty! A Phillps screw secures the switch cluster, grips and "choke lever" to the bars. I give it a twist. It moves but is very tight. There is a cable tidy which fits into a hole in the underside of the handle bar. It comes out with a fight. It is damage so it is discarded. There is an aftermarket switch for the riding lights. Two small screw secure the switch. They are removed.  Moving to the right side. Two Philips screws secure the switch cluster and throttle twist grip. Two Allen bolts secure the brake reservoir and lever. These come off in the normal way. There is a cable tidy which fits into a hole in the underside of the handle bar. It comes out with a fight. It is damage so it is discarded. The bars are secured to the upper yoke by four Allen bolts. They are very tight. I worry I might snap at least one of them. I give each one a small squirt of 3 in 1 oil. This does ease them a little. I find that red Locktight has been used on them, quite unnecessarily. The Locktight gives in and the bolts are wound out with some effort. Nothing snapped. The handle bars are now loose. It is necessary to remove the left side equipment first. The hand grip is very tight but it does move. Twisting backwards and forward and pulling at the same time works the grip off the bar. The clutch lever mount slips off quite easily. The bars can be pulled to the left which gives the necessary leeway to remove the throttle twist grip and cluster. We are fully committed now!

 

The new an old and new bars are subtly different to each other. The new bars are slightly raked back and up from the straighter and flatter  OEM items. There is the brace and the colour. The new items came from Hitchcocks. See the link in the side bar.   


 

Old v new bars

  To fitting of the new bars is the reverse of removing them. The throttle twist grip is slip on. The bar are pushed the right. The clutch lever mount is slipped on and pushed up the bars. The switch cluster and grip is force back on with a twisting motion. There is a residue of glue which will, no doubt, secure he grips as before. Now the clusters are in place the four bolts and the handle bar cap is refixed and bolts nipped up. They will be adjust later. On the inside of each cluster there is a locating pin. On the handle bar there is a hole. It was a bit fiddly to get he cluster with it pin the line up with the hole. A bit wiggling and check made the pin and holes line up. The bolt for the clutch lever is relocated and nipped up. The heated grip controller is refitted and 10mm nut and washer refitted. The right side the brake reservoir and lever is reattached and nipped up. I sit on the bike and move the handle bars to where I think  they feel right. I nip up the handlebar cap bolts to the correct setting. I tighten the screws of the left cluster making sure the "choke lever" operated correctly. The aftermarket switch for the riding lights has a brass coloured strap. When I removed the switch I took the strap and painted it black with rattle can. The painted strap is refitted. I adjust the attitude of the switch to make it easier to use. On the right side I tighten the screws for the switch cluster. I find the play in the throttle cable has disappeared. On the old bars there was significant amount of slack so when you twisted the throttle I had to take up more slack than I would like before the throttle actuated. 

With everything back in place I did an switch check. I turned the bike withe  key and went through each switch to make sure it activated the appropriate light. I also pulled the front brake lever to see if the rear brake light worked...it did. With some trepidation I hit the starter button. The bike cranked and started. I flicked the throttle a couple of times. It snapped back into place. The bike responded to the inputs and settled back to the normal tick over. The disappearing slack could have gone too far and pulled the throttle open at idle speeds. It did not and that is a result. I took the bike for a very quick spin to see that everything was in order.      

New handle bars

 I like the new aesthetic. You can see the slight rake to the bar if you compare the before and after pictures. There might be some subtle adjustment to be made the position of the bars and controls. I won't know until I go for an extended ride. I will take an Allen key and screw drive with me. I am hoping the raked bars will more comfortable on my wrists. Time will tell.    

Rear hugger

The hugger is a small mud guard that is fitted to the swing arm. It protects the shock absorber and the back the electric casing from the road crud thrown around by the rear tyre. This upgrade was a little more involved. 


                 

First the rear wheel had to come out. That involved breaking the chain at the link. Loosening the 24mm nut that secure the axle. The axle is removed and then the wheel can be removed. Then the area was thoroughly washed. It is difficult the clean this are with the wheel in place. I had a cup of tea and read the instructions whilst the area dried. 


 

The cable ties which were supplied in the kit were threaded though the upper slot as per the instructions. The swing arm fit in the recess. It is a snug fit and I tapped it home with the handle of my hammer. The cable ties were threaded around the swing arm and out through the bottom slot in the hugger. The ties were pulled tight, a further tap with the hame the make sure the hugger was fully seated and the ties took up a little slack. The hugger was fixed. The trimmed off the excess from the ties and that part of the job was done.

The last part was to refit the back wheel. The axle had to threaded through the near side swing arm picking up the chain adjuster on the way, this whilst holding the tyre off the road and keeping the chain ring and cush drive in the wheel. Wiggling the wheel and axle made it slip through the wheel hub, next the spacer had to be collected then the rear brake assemble this time whist ensure the disc brake pads went neatly either side of the disc rotor. Then to collect the off side chain adjuster then finally slip on the big washer and 24mm axle nut. The axle nut is just nipped up. The drive chain has to reconnected by offering up the chain to accept the split link. It was about now a realised why I have had bikes with shaft drives for years.For whatever reason the chain did not want get close enough for the fitting of the split link. I made sure the chain adjusters were slack, the axle loose enough to move and the chain was on the sprocket at the correct place. There was no reason it should not go back together. The chain is quite worn and lose. Close but not close enough. I remember an odd trick for this situation.

 

A cable tie is looped around the adjacent rollers and pulled tight. I spun the wheel backwards and forwards and low, the link came together. The split link was slid into lace. "o" rings slipped over the pins, the side plate installed a squeezed home finally the circlip was fitted remembering to put it one the right way - the fish swims up stream i.e closed end in the direction of rotation. And don't forget the remove the cable tie. Lastly the chain was adjusted to have 15 - 20mm of free play and the wheel to be on centre line of the bike. That quicker said than done. 

 

The hugger is quite out of sight. However, I expect it will help keep the worst of the road debris of the rear suspension unit and prolong its life. 

                                             




Fender Extender

 The fender extended will hopefully keep a bit more crud of the front of the engine. The existing mud guard does a reasonable job and the engine bash plate helps too. The bike already came with spacers to raise the front mud guard so mud does not clog between the tyre and guard. The extender was a cheap upgrade and a easy fix. 


 First I removed the four bolts holding the mud guard. The underside of the guard got a good washing. Any dirt would not help the extender sticking. I offered up the extender the mud guard and marked the edge. The kit comes with a cloth embedded with a cleaner. The cloth was rubbed all over the marked area on the underside the mud guard and opposite face on the extended.

 


 Next job was to arrange a stick the double side sticky pads to the extender. I also removed the makers sticker. I carefully peeled off the protective backing the sticky pads. Then ever so carefully positioned the extender under the mud guard and aligned the two parts. There was no second chances. The two elements were joined. they lined up nicely. 


 The kit contained four of these fiddly body poppers. An eight millimetre hole was drill at four points around the edge of the extender. The holes were cleaned up and popper inserted. The button was pressed down to secure the popper. Easy to do just fiddly and you have to be careful not to damage the finish on the existing mud guard.

 


 The top edge of the extender just need trimming back to make a smooth line into the existing mud guard. The mud guard was put back in place the risers and the fours bolts done up. Another small and cheap upgrade from Hitchcocks 

Head Light Stone Guard

 The guard is just a mesh to guard against something smashing the head light. Its not a problem I expect. I just got it for a bit of fun. There are many styles of head light guards. I went with a classic wire type from Hitchcocks.

Head light guard from Hitchcocks
The kit came with aluminium spaces and allen key bolts. 

The fitting was easy. I cleaned the headlight before I started. I undid the existing head light retaining Philips screws.Offered up the guard, slipped the spaced into place and screwed in the Allen bolts. I did one side at a time. Lining up the second bolt was a but fiddly until a moved the guard around on the headlight. The guard found it place and the bolt dropped into place. 

Head light before guard
Head light before   

 
Head light after guard
Head light after

The part fitted well. I expected it to sit a bit further away from the glass. I also think cleaning the head light is going to a trial. 

Tuesday, 29 July 2025

Rationalising the rats nest

The Himmy has a few additional accessories, riding lights and heated grip which came with the bike and a Sat Nav which I fitted. When lifted the seat to wire in the sat Nav I was presented with a rats nest of non-factory wiring. Wires were of differing sizes, bullet connectors, some soldered joint, some poorly wrapped with electrical tape others loosely shrink wrapped. I decided it needed tidying up.
 
I looked around the interweb for a box that would act as a distribution board. The idea was that a box would take a feed from the battery and the various accessories would be feed from the box. It also had to be small enough to fit under the seat. There are very few hidey holes on the himmy. I found the very thing in the Quick Wiring Fuse Box Battery Protection Junction Box. For this job the fuel tank and seats had to be removed. The seat come off easily but the tank needs two electrical connectors, fuel line and breather hoses to be disconnected.
 
 
  The DC 12v connects to the battery and there are four sets of terminals for the accessories. Each terminal set has a fuse, the blue LED means the circuit is good. It switches to red when there is an issue on the circuit. This sounds great except being directly connected to the battery and running the LEDs it means it will kill the puny battery on the bike in no time. I needed to find a switched feed from the bike so when the key is switch to off the accessory box is shut down as well. Part of the rats nest contained a switched feed. First the junction box had to be found a home that easily accessed. There is a scoop in the rear fender which accommodates the tool kit which is located under the rear seat. With the tool kit removed the junction box fitted in the space without affecting the fit of the seat. The box came with double sided tape. It was just a matter cleaning the place where the box was to live, fitting the tape to the box and the box to the fender. 
 
The 12v DC cable was threaded through the bike to be near the battery. The black (Negative) connector slipped snugly under the negative battery terminal. I just had to join the red wire from the box to the switched feed. The red wire from the box and switch feed wire were cut to slightly over length, the insulation stripped back and the wired twisted together and soldered. The joint was tightly wrapped with tape and tucked into the space between the frame and wiring harness. Now the power feed to the box reacted to the position of the ignition key.
 
The next job was to figure out what all the wires served and where they went. The Oxford heated grip had a nice long, paired wire which was connected the battery terminals. I disconnected the paired wires from the battery. I was necessary to cut off the inline fuse. It was no longer needed. The each outlet on the junction box is fused. This made the job of threading the wires thought frames to the junction box. The paired wires where cut to length, the insulation stripped and in this case the bare copper strands were tinned. This makes a tidy and secure base once they are pushed into their respective terminal and the screws fastened. The riding lights were a bit awkward. The wires feeding the lights were hacked into the main wiring loom. This meant they were always on. They also had some dodgy connectors and taping. Once I figured out the connection I tidied up the wires by cutting them back and soldering them together and covering with proper fitting heat shrink. The negatives from the lamps were earthed to the bike's frames. Having found the positive feed I routed that back to the junction box, cu the wire to length and stripped and tinned the end before connecting it to the junction box.
 
Fuse protected distibution box


The last accessory to tackle was the Sat Nav. To make it interesting the Sat Nav unit is over the handles bars and the junction box is under the rear seat. The power cable is quite long but would in be long enough? I started in the middle next to the battery. I threaded the Sat Nav power connector along the back bone of the frame, followed the wires path past the steering head and onto the instrument cluster. From there the wire was routed up the side and along the accessory bar to the Sat Nav mounting point. I had to fit the power lead into the Sat Nav cradle then attach the cradle to the mount. The cradle allows the Sat Nav unit to be quickly removed from the bike. The ball mount allows the cradle to positioned in front of the rider (me) where I read it with ease. I put small cable ties at likely points. The were loose for now. The reason for starting in the middle is that the Sat Nav power lead has a big blast resistor. It was easier for that to stay put and thread the small head unit to the mounting point. It took a little while to locate a home for the resistor unit to be fixed so that it did not foul the rider seat. It is about the size of a match box (35 x 25 x 20mm)  I found a recess in the air box which accommodated the resistor without fouling the seat. Double sided tape held in position. The wires from the resistor were led in and round the frame and wiring harness to the junction box. The wire were just long enough. The ends were already tinned so they were just plugged in the terminals and tightened up. All the wires were then tucked in next to the harness and zipped tied to secure them. 
 
Instrument cluster for the Himmy 411

      
 All the accessories were checked that they continued to work and obeyed the key. They did. Then it was case of refitting the tank which is a bit fiddly especially as it was full of petrol. The seat were fitted and rechecking everything worked and nothing was pinched. 
 
Spare wires and connectors

 The bikes is just a few ounces lighter than it was but it is a whole lot tidier and there is room for another powered accessory. I wonder what that shall be? 
 
Update: 
The bike has been stood for a few days and the bikes still has enough umph in the battery to start the bike. I am calling that a result.